8. Agitator & Pump

♧ Usages and applications
Lubrication oil, fuel oil, liquids with lubricating property


♧ Design and operation features
01. Applications
Lubrication oil, fuel oil, liquids with lubricating property

02. Differential pressure
Up to 6kg/cm².

03. Bearings
Internally setted metal bearing, lubricated by the pumping liquid.

04. Relief valve
Built-in type. Recommended Setting pressure is
132% of total pressure.
Setting pressure : minimum 2.2kg/cm² maximum 6.2kg/cm²

05. Shaft sealing
Gland packing or mechanical seal.

06. Pumping temperature
Up to 70°C in general(max.130°C)

07. Flanges
Suction and delivery KS or JIS 10kg/cm² rating.
Flange faces are flat faced.(FF)

08. Number of revolutions
Less than 400cst up to 1800rpm
Less than 500cst up to 1500rpm
Less than 1000cst up to 1200rpm~1000rpm

09. Viscosity
5~3000cst.

10. Standard capacity
calculated at 25.8cst(Rw.No.1, 100sec.),
Rpm-slip of motor is considered.
To keep the capacity at iscosity less than 25.8cst,
select bigger size or increase rpm.

* The out of the above range can be supplied
according to customer’s order placement


♧ Operating data
Capacity : 1m³/Hr ~ 30m³/Hr
Head : 2Kg/㎠ ~ 6Kg/㎠
Suction Bore : Ø32mm ~ Ø80mm

♧ Usages and applications

01. Application
Lubricating oil, Fuel oil or other liquids with property

02. Differential pressure
5~10kg/cm²

03. Bearings
Internally setted ball bearing or roller bearing,
lubricated by the pumping liquid.

04. Shaft sealing
Gland packing or mechanical seal.

05. Relief valve
Built-in type.
Setting pressure : minimum 5.5kg/cm² maximum 10.5kg/cm²

06. Pumping temperature
Up to 80°C (Normally up to 60°C)

07. Flanges
KS or JIS 10kg/ cm², FF

08. Number of revolutions
In general.

09. Viscosity
5~2000cst.

10. Standard capacity
Calculated at 25.8cst (Rw.No.1, 100sec.)
Motor rpm slip considered.

* The out of the above range can be supplied
according to customer’s order placement


♧ Operating data
Capacity : 40m³/Hr ~ 200m³/Hr
Head : 2Kg/㎠ ~ 10Kg/㎠
Suction Bore : Ø150mm ~ Ø250mm

▣ For pulp and paper industries,
and process industries.

♧ Usages and applications
Paper stock thru 6% consistency,
black liquor to 60% solids etc. in the pulp & paper industries.
Slurry handing, corrosive/abrasive crude, coke fines,
waste treatment, venturi scriber, textile slurries etc,
in the process industries.


♧ Design and operation features
01. Materials in gray cast iron, ductile cast iron, stainless steel etc.
02. Vertically split casing
03. Modified spiral volute casing.
04. Back pull-out design for low maintenance and downtime.
05. Open impeller.
06. Adjustable side plate and impeller.
07. Renewable shaft sleeve.
08. Oil lubricated bearings.
09. Rotation : Clockwise rotation viewed from the driver end.
10. Flanges are KS(JIS) 10kg/cm² ratings, FF
11. Dynamic Balance Seal Type (Option).

* The out of the above range can be supplied
according to customer’s order placement.


♧ Operating data
Capacity : 0.5m³/min ~ 67m³/min
Head : 5m ~ 80m
Suction Bore : Ø100mm ~ Ø500mm