7. Water & Wastewater Analyzer

(XonicⓇ 100MC)

♧ Application
Xonic 100MC measure flow velocity directly
with patented 4 path transducers.

Transducers are located at the end of each side to prevent
any obstructions, and level is located on the top of the open channel,
and accuracy is within 1% of actual flow.

Cross Flow Installation In case of winding open channel,
Xonic 100LM can use Cross Flow Installation to keep better accuracy.
Path 1 & 3, Path 2 & 4 can be installed
as cross path to keep better accuracy.


♧ Specification

• Principle
: Anti-Round Mode, TransitTime With Cross Correlation

• Measuring Path
: 2 or 4 path

• Measuring Width
: 30 meters

• Accuracy
: 2%

• Sensitivity
: 0.01 m/s

• Data Output
: 4-20mADC, Relay RS-232C / RS-485 ModBus

• Data Input
: 4-20mADC

• Datalogger
: 32Mbytes

• Display
: Large Color LCD (128x64)

• Temperature
: Range Electronics : -20 to +60℃
: Transducer : -40 to +120℃

• Power
: 110~220VAC, Free voltage

• Enclosure Electronics
: NEMA 4 (IP65) Transducer: Submersible (IP68)

(XonicⓇ 5L)

System Description Xonic5L is stainless steel,
no moving parts, battery operating,
fully digitalized Water Meter for municipal water applications.

Also, Xonic5L can measure clean water, dirty water, chemicals,
oil, alcohol, etc, so it can replace conventional flowmeters.

No Moving Parts
-No Turbine or Impeller
-No Gear Box
-No Magnetic Parts

Stainless Steel Body
-No Corrosiveness
-No Rust

Fully Digitalized Water Meter
-Ultrasonic Transit
-Time Method
-Bi-Direction Flow
-Empty Alarm
-9.5 Digit Total
-Total & Flow Indication
-Battery Operating (8 Years)
-Pulse Output (1m3/pulse)
-Same Size with Turbine


♧ Application
• Water Meter
• Flow Monitoring Flowmeter
• Flowmeters for
• Chemical
• Steel
• Semiconductor
• Ship Manufacturing
• Oil Refinery
• Irrigation

(XonicⓇ 100P)

Xonic 100P is fully digitalized,
easy-to-use portable flowmeter with only 2.4Kg weight.

The Xonic 100P connectors are submersible design which
can be used under harsh environmental conditions including rain
and sun light.

Basic model has two pair of transducer connectors for dual paths
or dual channels.

The Xonic 100P uses patent fine-timeTM DSP technology
to measure virtually any type of liquids with less than 30% solids
or bubbles, such as clean water, waste water, crude oil, etc.

• Clamp-On, Transit-Time
• 1 path, or dual path or 2 channel functions
• 20 hours battery operation
• IP67 Connectors,
• IP67 All Weather Case
• Submersible IP68 Transducers
• Touch Key programming + Remocon
• Large Color LCD Display
• Pulse Output
• Analog Output
• RS-232C Communication
• Datalogging Function with Xonic Software
• Weight 2.4Kg


♧ Application
- As Standard Flowmeter :
Xonic 100P can be used to check the performance of field flowmeters.
The Xonic 100P can be used to compare field flowmeters performance.

- As Field Flowmeter :
The Xonic 100P as portable device to spot-check
various flow installation for virtually any liquids of up to 30% solids
or bubbles.

- As Pipe Material :
Many kinds as CS Steel, SUS(SST), Cast Iron,
Ductile Iron, Aluminum, Brass FRP, PVC or Other
and Liner as: Mortar, Tar Epoxy, PE, Rubber or Other.


♧ Types of Liquids
The Xonic 100P has very strong signal,
which can measure various liquids such as clean water,
waste water, milk, manure, lime stone slurry, oil, gasoline, etc.

Normally, transit-time is only for clean water,
but Xonic 100P can measure all types of liquids using our patented
fine-time TM DSP technology.

- Clean Liquids
- Municipal Water, De-Ionized Water
- Acids, Benzene, Milk, Beer
- Crude Oil, Diesel, Alcohol
- Waste Water, Lime Stone Slurries, Manure


♧ Special Features
- Patented AR Mode
- Patented Fine
- TimeTM Measuring Technology
- DSP Functions
- Cross Correlation, FFT
- Oscilloscope Function
- Flow Velocity 0.02~12.0 m/sec
- Touch Key Programming + Remocon
- Large Color LCD Display
- 20 Hours Operation with Batteries
- Submersible Connectors Portable